Search Results:
- The connectivity problem occurred Monday morning. The inability to connect to the print server is the problem. Which condition is a symptom of a connectivity issue on a router that provides access to the Internet? An interface status is down. An...
- Escalate the issue to the desktop support group. Swap out the patch cable between the user PC and the switch to determine if that solves the problem. View the route table on the core router to determine if there is a routing issue. What is a benefit...
- What is the next step in the troubleshooting process? Determine an appropriate workaround. Escalate the problem to another department. Execute the rollback plan. To correct an issue that was discovered a few days earlier, an administrator makes a change during a regularly scheduled maintenance window. After making the change, the administrator discovers that a new problem has occurred. Gather information about the new problem and form a new hypothesis. Rollback the change and resume the troubleshooting process. Leave the change in place and troubleshoot the new problems at a later time. What are two situations where escalation of a case is recommended? Choose two.
- Choose three. Bidir-PIM is suited for multicast with larger numbers of sources. Available network bandwidth is overutilized outside of the multicast routing zone because multiple streams of data are required between distant routers in place of a single transmission. Choose two. Enable IGMP snooping in global configuration mode. Configure the IGMP snooping method. Enable multicast routing in global configuration mode.
- None - IGMP snooping is enabled globally by default. Bottom of Form 5 Top of Form Refer to the exhibit. PIM sparse mode has been also configured on all routers. After the first multicast packet is received by the Receivers and the switchover takes place, how will the multicast traffic continue to flow from the Source to the Receivers? The traffic will flow via source tree from the Source to the Receivers. Bottom of Form 6 Top of Form What is the result of the global configuration command ip pim send-rp-discovery Loopback0 scope 3? The router sends broadcast group-to-RP mapping messages so that other routers can automatically discover the RP. The routers sends group-to-RP mapping messages to The router sends group-to-RP mapping messages to The router advertises itself as the RP by sending messages to the Router R6 has sent a join message to router R4 requesting multicast traffic for users in the multicast group The multicast traffic will be dropped.
- The multicast traffic will be sent to switch SW1, which will drop the traffic. The multicast traffic will be forwarded to all users in the multicast group PIM should be configured only on the first and the last hop routers in the multicast tree. PIM should be configured on the device that hosts the source of the muticast traffic. PIM Sparse Mode is most useful when there are few senders, many receivers, and the volume of multicast traffic is high.
- PIM is a multicast routing protocol that makes packet-forwarding decisions independent of the unicast IP routing protocol that is running in the network. IP address All IP multicast group addresses fall in the range from IP addresses between It distributes the processing of Multiple devices can be grouped together to combine total bandwidth. The conversation flow can be split between multiple switches. The conversation flow can be split between multiple routers. Traffic shaping buffers excessive traffic to smooth traffic whereas policing drops excessive traffic. Traffic shaping is preferred for traffic flows such as voice and video whereas policing is better for TCP flows. Traffic shaping controls the rate traffic flows through a switch whereas policing controls traffic flows through a router.
- Create a separate VLAN for voice traffic. Utilize Power over Ethernet. Minimize the volume of the data traffic. Remove all QoS policies that are applied in the network. Implement access control lists at the distribution layer.
CCNP TSHOOT Chapter 2 Exam Answers (Version 7) – Score 100%.pdf
No service time limit Our only criterion is to ensure that you pass the exam. No matter when you go to the exam, we will serve you the day until you go to the exam. Hope you pass the exam successfully! If the test encounters a change, it will lead to disqualification. You can continue the service time free of charge by giving us the information that failed the test on the day. We will update and remind you all the latest news. Shipped within 24 hours All dumps are sent by mail. After we confirm your payment,you will receive dumps within 24 hours. Step 3: Take the time to study. Step 4: Pass the Cisco written exam! How often do you update your study materials?- We update in accord with the vendors if they change the question, our professional team will update our question and answer in a week. Do I have to pay for the updated information? Questions outdate of our service period and you will get special discounts. After order successfully, how can I get learning materials? All dumps are sent by e-mail. You will receive the dumps or workbooks during 24 hours after we confirm your payment. If not, please contact us. How do I pay for my order? If you don't have PayPal, you can bind your credit card via PayPal. Of course! All the question and answers are compiled by experienced experts after in-depth study of real exams and thousands of practice tests. You can definitely pass the exam in a short time with a high score. Jackson TT all correct. My mark is more than Dumps are stable. Just need to study well and pass. The exam computer is not very good, when I start to ping, it maybe not work. After 30 seconds, it work that maybe the program is running so don' t be nervous Filipe Antonio i am really happy for managing to pass the cert exam.
- Jason Hi, this exam is still valid kaunda hey guys? In addition, use premium files to revise the material and you will definitely succeed. If you want to take the exam, you must quickly Panos passhot is the best vendors of the dumps in the market, it let me pass the exam.
- Refer to the exhibit. An administrator is troubleshooting why host CL1 cannot communicate with the other hosts in the network. What appears to be the problem? VLAN is not being permitted on the trunk. A user is not able to use a VoIP phone. Based on the output, what could be the problem? The phone is in the wrong VLAN. The switchport mode is incorrect. QoS is missing. CDP is disabled. An administrator is troubleshooting a video multicast problem on router R1. Which statement correctly identifies the problem? Router R1 has not been configured with the ip multicast-routing command.
- After a major network upgrade, network users complain about poor video application performance. A network administrator verified that all trunk links are up and operational and the EtherChannel configuration is correct. The output of the show interfaces port-channel command reveals that there is a 0 packet output rate over the last 5 minutes on the Po2 uplink. What could be done to correct the issue? Users complained that they have experienced performance degradation for all video applications that are coming from the video server. Based on the provided outputs, what could be the possible cause of the problem? STP is blocking the redundant links that are bundled in both channels, thus causing the video traffic to be dropped.
- STP is blocking the redundant links that are bundled in the Po2 channel, thus causing half of the video traffic to be dropped. STP is alternating between channels when forwarding video traffic over the redundant links, thus causing a loss of video traffic. STP is blocking the redundant links that are bundled in the Po2 channel, thus causing the video traffic to be forwarded over the Po1 channel only. What three configuration commands are recommended to accommodate the addition of the phone? Choose three.
CCNPv7_Chapter 1 Exam_ Advanced Routing | I Pv6 | Virtual Private Network
Senior instructor and best-selling author Kevin Wallace shares preparation hints and test-taking tips, helping you identify areas of weakness and improve both your conceptual knowledge and hands-on skills. Material is presented in a concise manner, focusing on increasing your understanding and retention of exam topics. Exam topic lists make referencing easy. Chapter-ending Exam Preparation Tasks sections help drill you on key concepts you must know thoroughly. The companion CD-ROM contains a powerful testing engine that enables you to focus on individual topic areas or take complete, timed exams. The assessment engine also tracks your performance and provides feedback on a module-by-module basis, laying out a complete study plan for review.- Well regarded for its level of detail, assessment features, and challenging review questions and exercises, this official study guide helps you master the concepts and techniques that will enable you to succeed on the exam the first time. To find out more about instructor-led training, e-learning, and hands-on instruction offered by authorized Cisco Learning Partners worldwide, please visit www. Books in this series provide officially developed exam preparation materials that offer assessment, review, and practice to help Cisco Career Certification candidates identify weaknesses, concentrate their study efforts, and enhance their confidence as exam day nears.
Chapter 17: Quiz – Troubleshooting Redistribution (Answers) CCNPv8 ENARSI
Refer to the exhibit. Once AutoQoS is enabled the link goes down. What should the administrator do to correct this problem? Disable multilink on the PPP connection. Decrease the multilink threshold value to allow AutoQoS to run. Investigate the configured bandwidth on the PPP link to ensure it is sufficient, then remove and reapply the AutoQoS configuration. Further investigation reveals that the buffer pool continues to grow.- The CCO knowledge base identified the cause of the problem as a result of a buffer memory leak due to an IOS software bug. What should the administrator do to rectify this problem? Reload the router. Reinstall older Cisco IOS software. Upgrade the Cisco IOS software to a version that fixes the issue. Power down the router and wait a few minutes before reloading it. Change the configuration register settings to bypass the loading of the IOS.
- Change the configuration register settings to bypass the loading of the startup configuration file. A network administrator is troubleshooting the switching path on a router. Based on the exhibited output, what can be concluded? Fast switching has been enabled. Process switching has been enabled. Switching has been disabled. What should be done in the first phase of the automation process? In order to apply QoS policies, each interface should be configured with the auto qos command.
- Cisco Express Forwarding should be disabled on each target interface by the use of the no ip cef command. The network device should be configured to capture network traffic statistics via the use of the auto discovery qos interface configuration command. Via the use of the ip nbar protocol-discovery command, each interface should be configured to gather information about the applications that are known to NBAR. It is connected to a hub. It is operating within acceptable limits. It is carrying It has a duplex mismatch with the connected device. What can be determined from the exhibited output? There is a physical layer problem. The interface is performing normally. There is an unacceptable level of input errors. What are three indicators of a cabling issue on a switch? Choose three.
- Refer to the exhibit. Users on the LAN complained that they cannot access the Internet. Based on the provided output, what could be the possible cause of the problem? Too few addresses are assigned to the NAT pool. The NAT pool is configured with the wrong netmask. The configurations for the inside and outside interfaces are reversed. Refer to Chapter 6. Choose two. Users on the LAN complained that they cannot access the resources on the network. On the basis of the provided output, what could be the possible cause of the problem? The ip dhcp pool command is missing from the R2 configuration. The ip helper-address command is missing from the R2 configuration. The ip dhcp excluded-addresses command is missing from the R2 configuration. The domain-name command is missing from the R3 configuration. A network administrator issued show ip dhcp conflict command to verify the DHCP server operation on the router.
- Based on the provided outputs, what could be done to remedy the problem? Issue the dhcp services command on router R2. After issuing the show ip socket command and troubleshooting the problem, a network administrator verifies that the R1 and R2 interfaces are up and operational. The IP helper address is missing from the R3 configuration. Illegal addresses have been assigned to the interfaces of routers R1 and R2. Which procedure would solve this problem?
CCNPv7_Chapter 2 Exam_ Advanced Routing | I Pv6 | Network Protocols
We will update answers for you in the shortest time. Thank you! We truly value your contribution to the website. The help desk receives several calls on Monday morning stating that users cannot connect to a local print server that was working on Friday. Which statement about the problem would be correct? Which condition is a symptom of a connectivity issue on a router that provides access to the Internet? What is a symptom of an incorrectly applied network command when issued under the routing process? What is an important element of troubleshooting, regardless of the method used? A user creates a trouble ticket indicating that the Internet is inaccessible. The network administrator receives the ticket and determines that this user is the only one having problems. A ping command issued from the administrative PC to the user PC is successful. What should the administrator do next? What is a benefit of change control during the processes of regular network maintenance?- What is the first step of a structured troubleshooting process? Refer to the exhibit. What principles are depicted in the exhibit? Which element forms the basis of a good problem description?
- A network engineer is implementing redistribution of two routing protocols across a network topology. Under which situation would there be minimal concern of network visibility being hidden from the destination routing source? However, this is not an issue when there is only one point of redistribution between two sources. What is required for the redistribution process to successfully redistribute source information into the BGP process? The BGP process must have a route-map configured in order to set a metric for successful redistribution.
- The route to be redistributed must have a current entry in the routing table from the source routing protocol. Explanation: In order for any source information to be redistributed into a destination routing process, that information must currently exist within the source routing protocol RIB. If the route is removed from the source routing protocol RIB, the information is no longer able to be redistributed into the destination routing process.
- Refer to the exhibit. A network engineer has issued the exhibited commands on a boundary router. What is the result of these commands? The valid values for the AD are between 1 and ; a value of stops the installation of the route into the routing information base RIB. Which two statements define the behavior of a seed metric between dissimilar routing protocols? Choose two. It creates a distribute-list in global configuration mode. It uses the default-metric command. It creates an access-list in global configuration mode. It defines a prefix list in global configuration mode.
CCNP Routing And Switching TSHOOT 300-135 Official Cert Guide
It applies a route map configuration to the redistribute command. Explanation: There are three ways to define a seed metric when working with dissimilar routing protocols: Uses the default-metric command. Uses the metric parameter with the redistribute command. Applies a route map configuration to the redistribute command. Which keyword is not supported when redistributing IPv6 from a source to a destination routing protocol?- A network engineer is troubleshooting suboptimal routing on a network that may utilize redundant route redistribution. What should the engineer verify first? The engineer should verify the route tags being implemented within the redistribution process on the boundary router. The engineer should verify the default seed metrics being used within the redistribution process. The engineer should verify the subnets keyword being used within the redistribution process. The engineer should verify that mutual redistribution is occurring at multiple points in the network. Explanation: When troubleshooting suboptimal routing caused by redistribution, a network engineer must be able to recognize that mutual redistribution is occurring at multiple points in the network. A network engineer is reviewing the network topology and verifying route entries of a specific boundary router.
CCNA 2 (v + V) Chapter 2 Exam Answers For Static Routing - Config Router
Which two basic functions are performed by network security tools? Choose two. An administrator wants to use a network security auditing tool on a switch to verify which ports are not protected against a MAC flooding attack. For the audit to be successful, what important factor xhapter the administrator ccnp tshoot chapter 2 exam answers Which action will bring an error-disabled switch port back cvnp an operational state? Remove and reconfigure port chater on the interface. Issue the switchport mode access command on the interface. Clear the MAC address table on the switch. Issue the shutdown and then no shutdown interface commands. Refer to the exhibit. The Chapfer phone and PC work properly. Which two statements are true regarding switch port security?- The three configurable violation modes all log violations via SNMP. Dynamically learned secure MAC addresses are lost when the switch reboots. If fewer than the maximum number of MAC addresses for a port are configured statically, dynamically learned addresses are added to CAM until the maximum number capter reached. A network hcapter configures the port security feature on a switch. The security policy specifies that each access port should allow up to two MAC addresses. When the maximum number of MAC addresses is answerd, a frame with the unknown source MAC address is dropped and a notification is sent to the syslog server.
No comments:
Post a Comment